Salut a tous ,
J'ai ressuscité mon pcb .
Une micro projection d'étain sur 2 pistes etait à l'origine de ma "non reconnaissance" de mon PCB .
Je viens de faire mon flash et je ne suis pas vraiment sûre du resultat.
A la derniere question "voulez-vous passer en LT-plus", j'ai cliqué sur "non" en ne sachant quoi répondre .
Ai-je mal fait ?
Serial flash found with Status 0x72
Sending Device ID request to port 0x0000
Spi Status: 0x8C
Manufacturer ID: 0xC2
Device ID: 0x11
Flash Name: MXIC(MX25L2005)
Flash Size: 262144 bytes
Sending Spi UnLock request to Port 0x0000
......
Spi Status: 0x00
Getting Status from port 0x0000
Serial flash found with Status 0x72
Reading Drive Key.
............
Stage 1 failed
Authorisation Failed!
Getting Status from port 0x0000
Invalid Status 0x80
Sending Vendor Intro to port 0x0000
Status 0x80
Re-sending Vendor Intro:
....
Serial flash found with Status 0x72
Sending Device ID request to port 0x0000
Spi Status: 0x00
Manufacturer ID: 0xC2
Device ID: 0x11
Flash Name: MXIC(MX25L2005)
Flash Size: 262144 bytes
Sending Vendor Intro to port 0x0000
Serial flash found with Status 0x72
Sending Device ID request to port 0x0000
Spi Status: 0x00
Manufacturer ID: 0xC2
Device ID: 0x11
Flash Name: MXIC(MX25L2005)
Flash Size: 262144 bytes
Getting Status from port 0x0000
Serial flash found with Status 0x72
Reading Drive Key.
............
Authorised !
Grabbing sector 0x3E000.
................
Blank 3E000 sector detected!
Known f/w confirmed !
Sending Vendor Intro to port 0x0000
Status 0x51
Re-sending Vendor Intro:
....
Serial flash found with Status 0x72
Sending Device ID request to port 0x0000
Manufacturer ID: 0xC2
Device ID: 0x11
Flash Name: MXIC(MX25L2005)
Flash Size: 262144 bytes
Updating flash for on-line dump.
Sending Sector Erase to Port 0x0000
Erasing: 0x3E000
Writing: 0x3E000
............
Reading Bank 0: ................
Reading Bank 1: ................
Reading Bank 2: ................
Reading Bank 3: ................
Dumped in 7422mS
Restoring sector 0x3E000.
Sending Sector Erase to Port 0x0000
Erasing: 0x3E000
Writing: 0x3E000
............
Authorised !
................
Restore 0x3E000 verified !
Lite-On Dump file saved to Lite-OFW.bin
Loading firmware from buffer
Drive key @ n/a D5..............................2
Firmware Osig: [PLDS DG-16D4S 1071]
Firmware is: Stock
Key database updated
Drive is Slim Lite-On..
Key found in KeyDB at record (1 - lite-on orig 2)
Key is: D5..............................2
Key has been tested and verified, thanks C4eva !
EDIT : Quelqu'un pourrait me donner un tuto pour flasher mon pcb a l'aide du x360usbprov2 ?
(J'utilise la methode russe .)
Je veux être sûre de la méthode !
Pour l'instant , je fais un mix de ce que j'ai lu et cru comprendre.
Donc trop dans le doute .
Merci par avance .